On project 11, I have due similar to project 10. However, I have done additional demonstrations toward my temperature project on my Arduino breadboard. I have decided to revise the coding to use degrees in Celsius and Fahrenheit to show. I had trouble fixing my breadboard, so I had an additional breadboard to use in this project. The temperature detects voltage to Celcius, Celcius to Fahrenheit, and prints the Fahrenheit and Celcius temperature on the LCD screen. They are devices to measure temperature readings through electrical signals. The sensor is made up of two metals, which generate electrical voltage or resistance once it notices a change in temperature. My demonstration is to used the temperature sensor project to senor the cold weather outside the house and inside the room temperature. They are both differences between both since there. When you go outside, The temperature drops when you are outside than inside. The display screen provides the details of what is the temperature reading.
As learning in the project earns additional demonstration toward my project, then project 10. I always want to show improvement in each project what I have learned in these courses toward my future education or job position where I would like to teach a course. I always like to educate students and troubleshoot them to learn the problem that they are having. Once I have solved my problems in the educational experiences from the courses in my major. I could teach students are at a younger age to have these projects to learn from my experiences. Once you have troubleshooting, you can show the students the trouble that they would have. For instance, I have extra Arduino kits to use as spare parts or additional parts to used extra projects.
In Project 9 , I have decided to create led light with water sensor level. There are three light color for this project. In these light will shows which water sensor levels are. Each light changes show color change by putting in cup. When I put in the cup the blue and red lights come on. This show how much water level in the cup.
In this project , I have decided to create a led lights by using water sensor to show how much rain we have got. The red and mean we got the most and heavy rain along strong yellow led light. Once my water sensor is not in cup that means is not raining, show in blue led light.
I had to trouble shooting since not sure why my blue led light to come up so I to play with wires and the blue light has come on.
In Project 8, I have learned how to use the Tilt switch instead of a button switch. In the Tilt switch, we ran light that repeating several times such as light ran one by one as Digital light similar to rainbow light turn on many times as Once’s. We also needed to put many different, types resisters to order to get working. Also, we needed Digital sides (Jumpers) wires to work from the Controller board to breadboard the wires run from number 8 to 2. We needed to use the Loop to runs the repeat the lights to turn. For example led light can run any amount of sec. I have decided to run for a certain amount sec. I have chosen to do 5 sec in this project.
When I have done my demo on the breadboard, It becomes interesting because I have play breadboard not working so I have decided to switch sides I have a mistake by putting the wrong side or resisters issues. I have resolved the issue by changing the led side of light.
In, Project 5, I have spent 1 and a half hour to make water lever sensor work to work with LCD Display. Since I was playing around to see why or not is working or is working. I was able to fix it in the end my troubleshooting the wiring error. When I started to find the error is the power for the LCD then I was able to get on. Then I decided to make power for the water sensor in button. The display shows the amount of water level I get the cup. When I put water in full inside of the cup I will get a full water sensor gains the number of value is not in the cup Water sensor gain less. The wiring for the water sensor needed a male to female wire to attached to the breadboard or the controller board. I have spent 1 and a half hour to make water lever sensor work to work with LCD Display. Since I was playing around to see why or not is working or is working. I was able to fix it in the end my troubleshooting the wiring error. When I started to find the error is the power for the LCD then I was able to get on. Then I decided to make power for the water sensor in button. The display shows the amount of water level I get the cup. When I put water in full inside of the cup I will get a full water sensor gains the number of value is not in the cup Water sensor gain less. The wiring for the water sensor needed a male to female wire to attached to the breadboard or the controller board.
In Project 2, I have learned how to use a motor control sensor to connect the Stepper Motor board. In this project, I could not use regular jumper cable for this project so I used Male to Female Jumper cable to connect Stepper Motor to the controller board. The Stepper Motor board also has + and – charge to power up the lights. Each lights switches go A-D has switched around several number steps where you are going. When I feel the motor sensor it feels hot and moving. In the coding, I needed to create a Stepper control to move amount step where is going
In Project 1, We have to test a breadboard with a Potentiometer and a led light with resistors. I also needed + and – wires to work with the controller board on 5V and GRD, I had to connect them on those to work. 1 resistor and different jumper wires. However, This project is to learn how to do use Analog Read/ Write and Serial ports on the Controller board and coding.